Clamp body: high grade aluminium alloy, casted
Wedges: malleable cast iron, hot dip galvanized
Bimetallic casings: bimetallic sheet
screws: DIN 43161, A2 or Al,
spli pins: DIN 43161, A2
Clamp body: malleable cast iron, hot dip galvanized
Wedge: malleable cast iron, hot dip galvanized
screws: DIN 43161, hot dip galvanized
split pins: DIN 43161, A2
1) Contact wire AC acc. EN 50149 corr. Ri acc. DIN 43141 part 1
2) suitable for messenger wires made of copper or copper alloy acc. to DIN 48 201 part 1 or part 2
This type of clamp is not suitable for dead ends with contact wires made of copper magnesium alloy (for instance ""RiM..."").
Wedge: malleable cast iron, hot dip galvanized
Additional information
1) Contact wires ""F"" - dimensions for contact wire type AC acc. to EN 50149 (corresponding to Ri acc. to DIN 43141 part 1)
2) Ropes ""S"" - suitable for cables made of copper or copper alloys acc. to DIN 48201 Part 1 or Part 2
The assignment of the cross-sections to the wedges is also marked on the terminal housing as per fig. 5.
Clamp body: high grade copper alloy in different strengths forged resp. hard drawn
screws: DIN 933, A2-80
Clamp body: copper, forged
cover: copper alloy, forged
screws: acc. DIN 933, A2-80
nuts: acc. DIN 934, A2-80
Profile bars: copper, hard drawn
Clamp body: high grade copper alloy, forged
screw: countersunk screwA2-70
Clamp body picture 1: high grade copper alloy, hard drawn
Clamp body picture 2: high grade copper alloy, forged
Screw: acc. DIN 933, A2 or Cu
nuts: acc. DIN 934, A2 or Cu
Clamp body: high grade copper alloy, forged
screws: acc. DIN 933, A4-80
tab washer: E-Cu
Clamp body: high grade copper alloy, forged
screws: DIN 933 / A2-80
washer: WN 20 / A2
"Suitable for wires made of copper or copper alloy acc. to DIN 48 201 part 1 or part 2.
Note:
1) Cables 35 mm² - 95 mm² in a branch arrangement are held with at least 85% of the respective cable breaking force. In addition, 2 clamps must be used for a tension-resistant connection.
2) Cables 25 mm² - 50 mm² in a branch arrangement are held with at least 85% of the respective cable breaking force. In addition, 2 clamps must be used for a tension-resistant connection.
3) The use of a 25 mm² cable in the branch / as an auxiliary cable is only permitted in combination with the use of a 95 mm² and 125 mm² cable in the passage / as a messenger wire
4) Cables 70 mm² - 95 mm² in a branch arrangement are held with at least 85% of the respective cable breaking force. Connections 120 mm² - 150 mm² in the passage and branch achieve a holding force of at least 45 kN.
5) According to Ebs drawing, the clamp is intended for the cable combination 70 mm² / 120 mm² Bz II and 120 mm² / 120 mm² Bz II."
Clamp body: high grade copper alloy, forged
screws: DIN 933 / A2-80
washer: WN 20 / A2
Clamp body: high grade copper alloy, forged
Screws: DIN 933 / high grade copper alloy / A2-70
Nuts: DIN 934 / high grade copper alloy / A2-70
Crossing angle optionally 6° or 90°.
Before installation, the clamping points on the messenger cables must be cleaned of any adhering dirt and oxide layer using an appropriate steel wire brush.
Clamp body: high grade copper alloy, forged
Strap, bolt, and thimble: stainless stee
Screw: DIN 933 / A2-80
The 25 mm² and 35 mm² Bz II cables are held with at least 85% of their breaking strength.
Clamp body: high-grade forged copper alloy
Intermediate part: high-grade cast copper alloy
Straps, connecting bolts, bolts, washers, nuts: stainless steel
high grade copper alloy, hard drawn
Screws: DIN 933, A2-70
Nuts: DIN 934, A2-70
Clamp body: copper alloy, casted
Screws: special screw A4-80
Bolts: high grade copper alloy
split pin: copper
Clamp body: G-CuAl10Ni
Bolts, srew, nut: stainless steel A2
Double clevis twited: aluminium alloy
Beta-split pin: stainless steel